Introduction: Flushing a commercial R22 system for an R407C retrofit is mostly about diluting old mineral oil until the little that remains can no longer interfere with the new POE charge.
Retrofit projects usually start with a regulatory driver rather than an oil question. R22 sits among the HCFC refrigerants being phased out under the Montreal Protocol, and the EPA's SNAP program lists HFC and HFO substitutes such as R407C as replacements for residential and light commercial air conditioning equipment. Once the decision to convert is made, the practical work falls to the oil side of the job. A compressor that ran on mineral oil for fifteen years holds that oil in its sump, its oil separator, its coils, and its low points, and the new POE charge has to live alongside whatever is left. Understanding how flushing dilutes that residue, and why the residual number matters more than the flush product itself, is what separates a conversion that settles down from one that keeps coming back.
Why Mineral Oil Left Behind Matters in R407C Retrofits
Mineral oil and R22 were a matched pair. The refrigerant dissolved the oil readily, carried it through the evaporator and back down the suction line, and delivered it to the compressor sump where it belonged. R407C is an HFC blend and behaves differently with mineral oil: the two do not stay dissolved in each other, so any mineral oil that remains in the circuit after a conversion tends to separate out as its own phase. It collects where flow is slow, coats the inside of evaporator tubes, and sits in the receiver and accumulator instead of travelling with the refrigerant. In a system designed to move oil continuously, that is a problem with several faces. The first visible effect is heat transfer. A mineral oil film on the evaporator wall acts as an insulating layer between the refrigerant and the metal, and capacity drifts downward in a way that looks like a charge problem until someone inspects the oil. The second is oil return. Mineral oil that pools in the evaporator never reaches the compressor, so the sump level drops while the system still reads a normal refrigerant charge. The third is dilution of the new charge itself: leftover mineral oil mixes into the POE sump charge and shifts its viscosity and additive balance away from what the compressor was originally matched to. Old oil also carries the acidic breakdown products and sludge of years of service into a fresh charge.
How Multiple Flushes Dilute Residual Mineral Oil
Flushing works on dilution rather than removal. Every cycle drains the sump and the accessible low points, refills with fresh POE, circulates it through the circuit, and drains again. If a drain removes the large majority of the liquid it can reach, the amount of old mineral oil left behind after each cycle is a fraction of what was there before, and repeating the process drives the fraction down quickly. This is why the process is described in cycles rather than in hours. Documented product data for Emkarate RL68H, a synthetic POE in ISO VG 68 that is specified for HFC refrigerants including R407C, notes multiple flushing cycles for R22 to R407C retrofits and cites a residual mineral oil reference below 5%. That figure comes from following the cycle through, not from a single vigorous drain. A single pass falls short because of geometry. Oil separator elements, receivers, accumulators, suction line traps, and the lower circuits of a large coil all hold oil that gravity does not deliver to the drain plug. Flush oil has to circulate long enough, and under warm enough conditions, to pick up the film and the pooled pockets that a static drain cannot reach. Technicians running these jobs watch what comes out: colour, clarity, and the volume recovered against the volume charged tell them whether the circuit is still yielding old oil or has stabilised. Each cycle also gives the fresh POE time to work into the places where varnish and aged oil have settled.
What the 5% Residual Target Represents in Practice
The 5% reference is best understood as a miscibility and dilution benchmark, not a cleanliness score. It describes roughly where the remaining mineral oil stops being able to dominate the behaviour of the circulating charge, and it gives a retrofit team a stopping point that is tied to how the system functions rather than to how the drain looked. Four things sit behind that number and explain why technicians care about it.
- Miscibility sets the floor, because mineral oil and R407C separate into phases once the mineral share climbs past a modest level, and below that point the POE can keep the circulating oil dissolved and mobile through the evaporator.
- Metering devices are the narrowest point in the circuit, and undissolved mineral oil together with the waxy deposits it carries tends to gather at expansion valve orifices and small passages, so residual control protects the component most likely to plug first.
- Oil return depends on the charge behaving as a single miscible mixture, and keeping the mineral share low lets the POE travel back along the suction line and maintain sump level instead of leaving oil stranded in the coil.
- The residual figure itself is a sampling estimate taken from drain volumes rather than a laboratory measurement, so it tells a technician whether another cycle is worth the time before the final charge goes in.
Reading the number that way keeps it useful. A commercial chiller with a large receiver and long liquid lines holds more oil than a compact rooftop unit, and the number of cycles needed to reach a given residual varies with that geometry, with how long the system ran on mineral oil, and with how thoroughly the original drain was performed. The 5% figure comes from documented Emkarate RL68H product data as an example of a worked retrofit reference; the actual cycle count, flush volume, and acceptance point for any specific machine come from the compressor and equipment manual for that system.
Conclusion
An R22 to R407C conversion is a change of oil chemistry as much as a change of refrigerant, and the mineral oil left in the circuit is what most often decides whether the new POE charge performs the way it was selected to. Flushing in repeated cycles dilutes that residue step by step, and the residual reference gives the team a functional stopping point rather than a guess. Anyone planning this work should read the equipment manual first, then look at documented product data for the POE being charged, so the cycle count and acceptance point match the machine in front of them.
FAQ
Q: Why is mineral oil residue a concern in an R407C retrofit?
A: Mineral oil does not stay dissolved in R407C the way it did in R22, so residue left in the circuit separates into its own phase, coats evaporator surfaces, gathers at the metering device, and stops returning to the compressor. It also dilutes the fresh POE charge and shifts its viscosity and additive balance, which is why the old oil is dealt with before the new charge goes in.
Q: Why do R22 to R407C retrofits need more than one flush?
A: A single drain only reaches the liquid that gravity delivers to the drain point, while oil separator elements, receivers, accumulators, traps, and lower coil circuits hold oil that has to be picked up by circulating flush oil. Each cycle dilutes what remains, so several passes bring the residual down to a workable level; documented product data for Emkarate RL68H notes multiple cycles with a residual mineral oil reference below 5%.
Q: What does the 5% residual target help a technician understand?
A: It marks roughly where the remaining mineral oil stops dominating the behaviour of the circulating charge, so miscibility, oil return, and flow through the metering device stay within the range the POE was chosen for. It is a documented product reference rather than a universal field rule, and the cycle count and acceptance point for a specific machine follow its equipment manual.
Sources / References
Substitutes in Residential and Light Commercial Air Conditioning and Heat Pumps | US EPA
Section 608 Technician Certification | US EPA
No comments:
Post a Comment